What Do You Do When Your Door Lock Stops Working?

Test the lock with a key that was cut at a substitute open door unquestionably. In case the key isn't the issue, have a go at lubing up the lock using powdered graphite or a silicone-based oil. If you can turn your key when the doorway is open yet not when it's closed, the issue may be the plan of the entrance or lock. Or you can contact experts in  Emergency Lockout in Los Angeles.

1. Low Or Dead Batteries

One of the primary reasons why door locks equipped with keypads don't perform is because the batteries aren't fully recharged. If the lock you have is equipped with batteries, be sure to maintain them on a regular basis and change them as needed. The majority of keypad locks include indicators to monitor battery levels which inform you when it's time to replace the batteries.
Most keypad locks use 4 four and AAA batteries. You can likely purchase them from the supermarket near you.
To replace the batteries, you need to open the door and look for the compartment which is home to the battery. If you locate it, replace the batteries that were in use with new ones. If the above steps don't work, attempt a different approach to solve the issue.

2. Keypads That Are Not Aligned

There may be a reason that your keypad doesn't match up with the deadbolt when it's not working. It's usually the case when you install the lock yourself and have failed to check your keypad has been properly aligned.
Look at the top of the keypad while you open the doors to fix this. You will see two screws you can loosen to change the keypad. Once you've loosened the screws then try operating the keypad again to verify if it is working.

3. Keypads That Have Been Wet Or Dirty

In some cases, the keyboard might not be active or working properly because dirt or water can cause an electrical disturbance. In this situation, it's essential to clean the keypad with a clean cloth or compress air before trying to utilize it.
To clean keys, you can use an absorbent cloth and ruby alcohol. Clean the keys until they're clean. Test operating the lock one more to determine if it's working.

what-do-you-do-when-your-door-lock-stops

4. Defective Keypad

Although it's not a typical scenario, it's possible the keypad has been damaged. You can replace the keypad by yourself should it be damaged. If you're not confident whether you can do it yourself it is possible to hire an expert locksmith to take care of it for you.

5. Loose Wiring

Another reason why the keypad lock you've installed may not function could be because of an unconnected wire. Locks usually break when they aren't properly installed because screws aren't seated properly. The wires become loose with time, and they stop working. Make sure a Car Locksmith does proper work. To correct this issue you must follow the directions to follow the steps below:

  1. Lock the doors, then examine the opposite side to the side of the keypad. You'll find a small hole with one tiny screw in its middle.
  2. Secure the screw using it using the Phillips screwdriver.

6. Frozen Keypad

If the keypad on the door lock does not respond It's possible that the lock is frozen. This is typically the case in cold temperatures when the moisture in the air expands which is then taken up by the lock's keypad.
To get rid of keys that have frozen, it is possible to use a hair dryer to melt snow. When the ice has melted and the keys are clean then you can clean it off with a dry towel to remove any water.

7. Deadlock Mode

Certain keypad locks come with deadlock modes that disable the keypad if it's not being used for a specific period of time. This usually happens to help conserve battery energy.
If the keypad lock is locked in deadlock mode, it's going to require you to enter a password to open it. Once the keypad is activated, you're now ready to use it just like it would normally.

what-do-you-do-when-your-door-lock

8. There Are Something Blocking the Sensors

A sensor blockage could cause a keypad lock to fail. The sensor reads the code that you enter using the keys. If there's a problem with the sensor's capability to read, it may hinder the code from being read correctly.
This usually occurs when sensors are filthy or have an accumulation of dirt. To get rid of it, clear off any obstructions that may hinder the sensor and then try it again. You can also clean the sensors using dried cloths as well as compressed air.

9. The Battery Compartment Isn't Functioning Properly

The compartment housing the battery that is in the keypad on your door lock may be damaged if it isn't functioning. The most common cause of damage to batteries is when they aren't properly inserted and the space is damaged.
Locate the battery compartment by opening the compartment. Be sure to put the batteries back into the compartment if they don't work. If all else fails, it's possible to engage someone who is an experienced locksmith to do the task.